For André Vrecer, a refit is like restoring a classic car: a boat arrives that barely still floats and runs, and it leaves as a new one. How Werft 52 on the Swiss shore of Lake Constance renews boats in wood, steel and fibreglass to their owners’ wishes, from the wiring to a complete overhaul.
Anyone who has a classic car restored rarely brings in one that is still in good shape. He brings one that shows its years, and collects a car that looks and drives the way it should again. André Vrecer, owner of Werft 52 AG in Romanshorn, compares his work on boats to exactly that.
For more than 40 years Werft 52 has worked on the Swiss shore of Lake Constance, with its head office in Romanshorn for motorboats and a branch in Kreuzlingen for sailing boats. New and used boats, servicing and winter storage are part of the house’s everyday work. One focus, though, is boats whose owners want them renewed rather than replaced.


What a refit is
The yard puts it plainly: a refit is the renovation of a yacht entirely to its owner’s wishes. It can be a partial renovation that concerns only the wiring, for example, or a complete overhaul. So the scope is set not by a catalogue but by the boat and the person who owns it. “Almost anything is possible, from a technical upgrade to aesthetic refinement,” as Werft 52 puts it.
What that means in practice is shown by a list the yard draws up itself. It reads like a collection of the small annoyances an owner will at some point no longer accept:
- Under way: the yacht is too slow, the controls are outdated, it cannot make headway against the current of a river or against waves and wind.
- Quiet on board: the freshwater pump makes too much noise as soon as someone turns on the tap, and the toilets are too loud.
- On deck: the canopy is a nuisance to close, and the fenders get in the way when they are stowed.
- At the stern: there is no door to the bathing platform, the steps to the aft deck are awkward, the bathing platform is too narrow.
For each of these points, the yard promises, there is the right solution. A refit therefore begins with a simple question every owner can ask himself: what bothers me about my boat?
A refit is like restoring a classic car: you bring in a broken boat that barely still floats and runs, and we turn it into a new one.
Wood, steel and fibreglass
Werft 52 carries out refit work in three materials: wood, steel and fibreglass, that is glass-reinforced plastic. For steel yachts the house has seen itself as the place to go on the lake for decades. The work is most visible, though, on wooden boats, because on them every flaw and every coat of varnish lies open to the eye.
The photographs from the workshop show how such work begins. A meter checks how damp the wood is. A strip of wooden trim shows damaged varnish, an opened panel reveals the damage behind it. Only once it is clear what lies beneath the surface can anyone say what a boat needs.



That woodwork, varnish and engineering stay in one pair of hands is down to the site. Werft 52 has its own boatbuilder and its own boat painter right on site, plus a crane for boats of up to 20 tonnes and a modern transport system that moves boats around the grounds. So a boat does not have to leave the site for a new coat of varnish. In Kreuzlingen, home of the sailing boats, the yard also has its own rigging crane, and underwater antifouling, the protection of the hull below the waterline against fouling, is part of the service too.


Today’s technology in a classic boat
A refit is no journey back in time. With classic boats it is often about keeping the lines, the wood and the character, and fitting technology behind them that meets today’s standards. In one of the photographs from the workshop, a modern chartplotter sits in a console of varnished mahogany, with cup holders and trays set into the wood. The boat looks as it always did and navigates as boats do today.

The owners’ wishes reach far beyond the cockpit: new controls, a quieter pump, more power against wind and waves. For the engines, the yard has service technicians who specialise in Mercruiser, Mercury, Volvo Penta, Steyr and Nanni, and direct access to the entire Volvo Penta parts range. Anyone who wants to switch to electric propulsion altogether will find the specialists for that too: Werft 52 is a dealer for ePropulsion and for Mercury’s Avator electric outboards, and handles conversions, retrofits and servicing for electric drives.
Renew rather than replace
The yard keeps its own count of how much of this has already passed through the workshop: more than 8 restorations and over 15 refit projects. Behind each of these numbers is an owner who wanted to renew his boat rather than replace it.
Anyone who wants to know, before a refit, what condition a boat is in and what it is worth will also find someone to talk to at Werft 52. André Vrecer is a technical boat surveyor. He assesses and values damage, prepares damage reports and draws up purchase and valuation surveys.
Then there is everything that makes up a yard on the lake throughout the year: a heated workshop of 350 square metres in Romanshorn and a workshop of 450 square metres in Kreuzlingen, more than 185 boats in winter storage, an on-call service around the clock and its own young talent, because the yard trains boatbuilders and boat technicians. Werft 52 is a member of the Swiss motorboat association FSM.
Back to the classic car. You do not give up on a well-built classic because the wiring fails or the paint has grown tired. Boats are no different. What a particular boat needs depends on the boat and on its owner’s wishes. The refit work of Werft 52 in wood, steel and fibreglass gives an idea of what is possible.
Questions we get asked
What is a refit?
The renovation of a yacht entirely to its owner’s wishes. It ranges from a partial renovation, for example of the wiring only, to a complete overhaul.
Which materials does Werft 52 work in for a refit?
Wood, steel and fibreglass. The yard has its own boatbuilder and its own boat painter right on site, plus a crane for boats of up to 20 tonnes.
Where is Werft 52?
On the Swiss shore of Lake Constance. The head office in Romanshorn specialises in motorboats, the branch in Kreuzlingen in sailing boats.





